F1 |
NTC sensor short-circuited water / heating |
F2 |
NTC sensor open-circuited water / heating |
F10 |
Water intake |
F11 |
Water drainage |
F15 |
Water intake fault - Hot water |
F16 |
Foam / Excess detergent |
F19 |
Flow meter slow / difficult to rotate |
F20 |
Heating |
F39 |
Electronic unit fault BAE (Control and Displayelectronic) |
F41 |
Faulty EEPROM / incorrect data |
F43 |
Model type not programmed |
F45 |
Flash RAM defective / Incorrect data |
F46 |
LCD connection defective |
F47 |
BAE/ SLT interface defective |
F50 |
Drive |
F51 |
Level switch, pressure sensor |
F53 |
Speed sensor fault |
F56 |
Final spin speed < 400 rpm |
F62 |
programmee selector defective (DWS)+B97 |
F63 |
Water path control unit fault |
F64 |
Path sensor defective |
F65 |
Drum lighting cap missing |
F92 |
Bacterial contamination risk |
F93 |
Additional relay module defective |
F104 |
drive / low voltage (z.B. Klixon, low voltage FU) |
F4000 |
no fault |
F4001 |
water im suds container |
F4002 |
Trommelbewegung, door kann nicht open werden |
F4003 |
door kann open werden |
F4004 |
door is open |
F4005 |
door is closed |
F4006 |
control has restricted water level |
F4007 |
control has increased water level |
F4008 |
No money |
F4009 |
not enough money for programme |
F4010 |
Exceeded max programme time, overlay safety time expired |
F4011 |
fault frequency converter |
F4012 |
fault over-current frequency converter |
F4013 |
fault frequency converter intermediate circuit voltage too small |
F4014 |
fault frequency converter intermediate circuit voltage too high |
F4015 |
fault frequency converter slip too high |
F4016 |
fault frequency converter imbalance not appropriate |
F4017 |
A programmed programme stop is carried out |
F4018 |
A programmed spin stop is carried out |
F4019 |
A programmed starch stop is carried out |
F4020 |
A programmed spin and starch stop is carried out |
F4021 |
programme stops due to maximum load switch off |
F4022 |
The fluff filter cap of the dryer is open |
F4023 |
control waits with programme start while an external exhaus air flap is opened |
F4024 |
control detects a too high value at the NTC-temperature sensor SER_MSG_FAULT_HOCHOHMIG |
F4025 |
control detects a too high value at the NTC-temperature senso, SER_MSG_FAULT_NIEDEROHMIG |
F4026 |
Crease control after programme end |
F4027 |
Fluid dispenser fault during rinse |
F4028 |
control recognizes Chip card |
F4029 |
Remark fluff filter dirty |
F4030 |
fault notification load sensor faulty |
F4031 |
Remark fault sensor drive system fault |
F4032 |
SER_MSG_DOOR_CONTACT |
F4033 |
SER_MSG_DOOR_OPEN |
F4034 |
SER_MSG_DOOR_CLOSED |
F4035 |
SER_MSG_DOOR POSITION_KONT |
F4036 |
SER_MSG_WATER_TAP_CLOSED |
F4037 |
SER_MSG_WATER_PRESSURE_SMALL |
F4038 |
SER_MSG_WATER_LEVEL_SMALL |
F4039 |
heater defect, SER_MSG_HEATER_FAULT |
F4040 |
heat output too small, SER_MSG_HEATER_TOO_SMALL |
F4041 |
heat output too high, SER_MSG_HEATER_TOO_BIG |
F4042 |
relay 1K1/1 is defect, SER_MSG_SCHUETZ_1_FAULT |
F4043 |
relay 2K1/1 is defect, SER_MSG_SCHUETZ_2_FAULT |
F4044 |
SER_MSG_NTC_1_SHORT |
F4045 |
SER_MSG_NTC_1_OPEN |
F4046 |
SER_MSG_NTC_2_SHORT |
F4047 |
SER_MSG_NTC_2_OPEN |
F4048 |
SER_MSG_ABL_VALVE_DEFECT |
F4049 |
SER_MSG_ABL_VALVE_CLOGGED |
F4050 |
SER_MSG_ABL_VALVE_LEAKY |
F4051 |
SER_MSG_SLT_FU_COM_FAULT |
F4052 |
SER_MSG_MFM1_FAULT |
F4053 |
SER_MSG_MFM2_FAULT |
F4054 |
SER_MSG_MFM3_FAULT |
F4055 |
SER_MSG_MFM4_FAULT |
F4056 |
SER_MSG_MFM5_FAULT |
F4057 |
SER_MSG_TACHO_FAULT |
F4058 |
SER_MSG_TACHO_SPG_SMALL |
F4059 |
SER_MSG_DOOR RELEASE_1 |
F4060 |
SER_MSG_DOOR RELEASE_2 |
F4061 |
SER_MSG_CHIP CARD_FAULT |
F4062 |
SER_MSG_CHIP CARD_SCHALTER |
F4063 |
SER_MSG_MEMORY CARD_FAULT |
F4064 |
SER_MSG_SMALL_MEMORY_CARD |
F4065 |
SER_MSG_MEMORY |
F4066 |
SER_MSG_CLOCK_MODUL |
F4067 |
SER_MSG_BEL_MODUL |
F4068 |
SER_MSG_FU_MODUL |
F4069 |
SER_MSG_NTC_DRAWN |
F4070 |
SER_MSG_MACHINE TYPE |
F4071 |
SER_MSG_HEATER TYPE |
F4072 |
SER_MSG_FAULT_BAE |
F4073 |
MSG_DUMMY_1 |
F4074 |
MSG_DUMMY_2 |
F4075 |
MSG_DUMMY_3 |
F4076 |
MSG_DUMMY_4 |
F4077 |
MSG_DUMMY_5 |
F4078 |
MSG_DUMMY_6 |
F4079 |
MSG_FLIP_FLOP_ABGEFALLEN |
F4080 |
internal fault BAE |
F4081 |
Multi functional module EZL 230 signed in with code 1, code not recognized |
F4082 |
Multi functional module EZL 230 signed in with code 2, code not recognized |
F4083 |
Multi functional module EZL 230 signed in with code 3, code not recognized |
F4084 |
Multi functional module EZL 230 signed in with code 4, code not recognized |
F4085 |
Multi functional module EZL 230 signed in with code 5, code not recognized |
F4086 |
Multi functional module EZL 230 signed in with code 6, code not recognized |
F4087 |
Multi functional module EZL 230 signed in with code 7, code not recognized |
F4088 |
Multi functional module EZL 230 signed in with code 8, code not recognized |
F4089 |
Multi functional module EZL 230 signed in with code 9, code not recognized |
F4090 |
Multi functional module EZL 230 signed in with code 10, code not recognized |
F4091 |
Multi functional module EZL 230 signed in with code 11, code not recognized |
F4092 |
Multi functional module EZL 230 signed in with code 12, code not recognized |
F4093 |
Multi functional module EZL 230 signed in with code 13, code not recognized |
F4094 |
Multi functional module EZL 230 signed in with code 14, code not recognized |
F4095 |
Multi functional module EZL 230 signed in with code 15, code not recognized |
F4096 |
Code switch 14X on ELP 230, mashine type and heater type not recognizes. Mashine type not recognized |
F4097 |
Code switch 14X on ELP 230, mashine type and heater type not recognizes. Mashine type not recognized |
F4098 |
fault FU |
F4099 |
fault timer-Modul |
F4100 |
fault data memory |
F4101 |
fault BW-data |
F4102 |
fault check sum operating system |
F4103 |
fault check sum work copy |
F4104 |
fault check sum current name |
F4105 |
fault check sum blcok name |
F4106 |
fault check sum programme list |
F4107 |
fault check sum Block list |
F4108 |
fault check sum appliance status |
F4109 |
fault check sum Kanden setting |
F4110 |
fault check sum Service setting |
F4111 |
fault check sum language |
F4112 |
fault check sum input/output-allocation |
F4113 |
FAULT_CS_SYSTEM COMPONENT |
F4114 |
fault check sum programme memory |
F4115 |
fault check sum Block memory |
F4116 |
fault check sum mashine history |
F4117 |
fault check sum operation data |
F4118 |
fault check sum faults statistic |
F4119 |
fault check sum operation fault |
F4120 |
FAULT_CS_DRYER_LOW PRESSURE TABLE |
F4121 |
fault check sum Standard programme |
F4122 |
fault check sum Standard block |
F4123 |
fault Backup-matching |
F4124 |
fault motor without rotation |
F4125 |
time overrun (Timeout) in communication between control ELP 230 and frequency converter EFU 230. |
F4126 |
fault drive Tacho |
F4127 |
fault drive Tacho after safety time |
F4128 |
fault drive Tacho in programme stop |
F4129 |
fault drive Tacho in programme stop |
F4130 |
fault drive FU-safety brunt |
F4131 |
fault drive Motor klixon |
F4132 |
FAULT_POSITION_NOT_ADJUSTED |
F4133 |
FAULT_POSITION_ADJUSTED |
F4134 |
fault imbalance |
F4135 |
fault imbalance switch |
F4136 |
fault heating system NTC1 |
F4137 |
fault heating system NTC1 Desinfection |
F4138 |
fault heating system TGS a contact |
F4139 |
relay contact 13,14 on 1K1/1 and/or 2K1/1 interrupted in heat up phase |
F4140 |
relay contact 13,14 an 1K1/1 and 2K1/1 closed outside heat up phase |
F4141 |
FAULT_HEATING SYSTEM_TGS_DURING_HEATING PHASE |
F4142 |
FAULT_HEATING SYSTEM_TGS_MEMORY |
F4143 |
FAULT_THERMOSTOP |
F4144 |
switch door lock 2F6/6 does not switch or motorklixon F3 has tripped |
F4145 |
FAULT_DOOR LOCK_RELEASE |
F4146 |
FAULT_DOOR LOCK_DOOR_OPEN |
F4147 |
FAULT_DOOR LOCK_DOOR_CLOSE |
F4148 |
FAULT_DOOR RELEASE SIGNAL |
F4149 |
fault Notentriegelung door open |
F4150 |
FAULT_SAFETY LOCK_DOOR_CLOSED |
F4151 |
no level increase within 5 minutes. |
F4152 |
switch 3S57 interruption |
F4153 |
Analog pressure sensor recognize overflow level or is faulty |
F4154 |
fault drainage |
F4155 |
fault drainage spin |
F4156 |
safety pilot notifies a fault (F10, exit 3) |
F4157 |
level switch 2B1/13 has connected (contact 1-3 closed) |
F4158 |
level switch 1B1/13 has connected (contact 1-2 closed) |
F4159 |
fault check dispenser system F4160 Until ID 846: level switch B1/1, contact 1-3, when dispenser open. From ID 1000: electric connector on dispenser module (plug 40X GND-IN 7 defect). |
F4161 |
timer for greasing the mount exceeded |
F4162 |
timer for Service exceeded |
F4163 |
timer for BGR-check exceeded |
F4164 |
Analoger-pressure sensor on ELP 230 defect. |
F4165 |
Interruption plug EB 230 65X, to ELP 230 30X. Or EB 230 defect. |
F4166 |
fault cradle system in programme F4167 fault net interruption |
F4168 |
FAULT_CHIP CARD_SLT |
F4169 |
FAULT_CHIP CARD_BAE |
F4170 |
To ID 846: internal fault status 1 door state. From ID 1000: internal fault control at data back-up Service setting |
F4171 |
To ID 846: internal fault Status 2 door state. From ID 1000: internal fault of control at data back-up of the input/output list |
F4172 |
To ID 846: internal fault Status 3 doort status. From ID 1000: internal fault of control at data back-up of system parts list |
F4173 |
FAULT_PROGRAMME LIST |
F4174 |
internal fault |
F4175 |
FAULT_INTERRUPT |
F4176 |
FAULT_TASK |
F4177 |
internal fault |
F4178 |
internal fault |
F4179 |
internal fault |
F4180 |
internal fault |
F4181 |
internal fault |
F4182 |
internal fault |
F4183 |
FAULT_FANKLIXON_INTERNAL_RUNNING |
F4184 |
FAULT_FANKLIXON_EXTERNAL_RUNNING |
F4185 |
FAULT_TEMPERATURE_BEFORE_START |
F4186 |
fault copy flashcard |
F4187 |
internal fault |
F4188 |
internal fault |
F4189 |
internal fault |
F4190 |
internal fault |
F4191 |
internal fault |
F4192 |
internal fault |
F4193 |
internal fault |
F4194 |
internal fault |
F4195 |
internal fault |
F4196 |
internal fault |
F4197 |
internal fault |
F4198 |
internal fault |
F4199 |
internal fault |
F4200 |
internal fault |
F4201 |
internal fault |
F4202 |
internal fault |
F4203 |
internal fault |
F4204 |
ROOM THERMOSTAT_8F1 |
F4205 |
ROOM THERMOSTAT_9F1 |
F4206 |
FAULT_EXHAUST AIR_NTC |
F4207 |
FAULT_TOOLUFT_NTC |
F4208 |
FAULT_PRESSURE GAUGE_TR |
F4209 |
internal fault |
F4210 |
internal fault |
F4211 |
internal fault |
F4212 |
internal fault |
F4213 |
FAULT_DUMMY_6 |
F4214 |
internal fault |
F4215 |
internal fault |
F4216 |
internal fault |
F4217 |
internal fault |
F4218 |
internal fault |
F4219 |
internal fault |
F4220 |
internal fault |
F4221 |
internal fault |
F4222 |
internal fault |
F4223 |
internal fault |
F4224 |
internal fault |
F4225 |
internal fault |
F4226 |
internal fault |
F4227 |
internal fault |
F4228 |
internal fault |
F4229 |
internal fault |
F4230 |
internal fault |
F4231 |
internal fault |
F4232 |
internal fault |
F4233 |
internal fault |
F4234 |
internal fault |
F4235 |
internal fault |
F4236 |
internal fault |
F4237 |
internal fault |
F4238 |
internal fault |
F4239 |
internal fault |
F4240 |
internal fault |
F4241 |
internal fault |
F4242 |
internal fault |
F4243 |
internal fault |
F4244 |
internal fault |
F4245 |
internal fault |
F4246 |
internal fault |
F4247 |
internal fault |
F4248 |
internal fault |
F4249 |
internal fault |
F4250 |
internal fault |
F4251 |
internal fault |
F4252 |
internal fault |
F4253 |
internal fault |