| F1 |
NTC sensor short-circuited water / heating |
| F2 |
NTC sensor open-circuited water / heating |
| F3 |
NTC sensor short-circuited air path / fan |
| F4 |
NTC sensor open-circuited air path / fan |
| F39 |
Electronic unit fault BAE (Control and Displayelectronic) |
| F40 |
Electronic unit fault |
| F41 |
Faulty EEPROM / incorrect data |
| F42 |
No mains frequency recognition |
| F43 |
Model type not programmed |
| F44 |
I²C bus defective |
| F45 |
Flash RAM defective / Incorrect data |
| F46 |
LCD connection defective |
| F47 |
BAE/ SLT interface defective |
| F55 |
Overriding time control overruned |
| F66 |
Air path leakage |
| F100 |
Communication link failure to IK6 (faulty / interruped) |
| F101 |
IK6 faulty / incompatibilty |
| F151 |
fault no ionisation |
| F152 |
fault coil fault magnet valve |
| F153 |
fault over temperature Gas-burner |
| F154 |
fault internal ZFA-fault |
| F155 |
fault parasitic-flame |
| F4000 |
no fault |
| F4001 |
water im suds container |
| F4002 |
Trommelbewegung, door kann nicht open werden |
| F4003 |
door kann open werden |
| F4004 |
door is open |
| F4005 |
door is closed |
| F4006 |
control has restricted water level |
| F4007 |
control has increased water level |
| F4008 |
No money |
| F4009 |
not enough money for programme |
| F4010 |
Exceeded max programme time, overlay safety time expired |
| F4011 |
fault frequency converter |
| F4012 |
fault over-current frequency converter |
| F4013 |
fault frequency converter intermediate circuit voltage too small |
| F4014 |
fault frequency converter intermediate circuit voltage too high |
| F4015 |
fault frequency converter slip too high |
| F4016 |
fault frequency converter imbalance not appropriate |
| F4017 |
A programmed programme stop is carried out |
| F4018 |
A programmed spin stop is carried out |
| F4019 |
A programmed starch stop is carried out |
| F4020 |
A programmed spin and starch stop is carried out |
| F4021 |
programme stops due to maximum load switch off |
| F4022 |
The fluff filter cap of the dryer is open |
| F4023 |
control waits with programme start while an external exhaus air flap is opened |
| F4024 |
control detects a too high value at the NTC-temperature sensor SER_MSG_FAULT_HOCHOHMIG |
| F4025 |
control detects a too high value at the NTC-temperature senso, SER_MSG_FAULT_NIEDEROHMIG |
| F4026 |
Crease control after programme end |
| F4027 |
Fluid dispenser fault during rinse |
| F4028 |
control recognizes Chip card |
| F4029 |
Remark fluff filter dirty |
| F4030 |
fault notification load sensor faulty |
| F4031 |
Remark fault sensor drive system fault |
| F4032 |
SER_MSG_DOOR_CONTACT |
| F4033 |
SER_MSG_DOOR_OPEN |
| F4034 |
SER_MSG_DOOR_CLOSED |
| F4035 |
SER_MSG_DOOR POSITION_KONT |
| F4036 |
SER_MSG_WATER_TAP_CLOSED |
| F4037 |
SER_MSG_WATER_PRESSURE_SMALL |
| F4038 |
SER_MSG_WATER_LEVEL_SMALL |
| F4039 |
heater defect, SER_MSG_HEATER_FAULT |
| F4040 |
heat output too small, SER_MSG_HEATER_TOO_SMALL |
| F4041 |
heat output too high, SER_MSG_HEATER_TOO_BIG |
| F4042 |
relay 1K1/1 is defect, SER_MSG_SCHUETZ_1_FAULT |
| F4043 |
relay 2K1/1 is defect, SER_MSG_SCHUETZ_2_FAULT |
| F4044 |
SER_MSG_NTC_1_SHORT |
| F4045 |
SER_MSG_NTC_1_OPEN |
| F4046 |
SER_MSG_NTC_2_SHORT |
| F4047 |
SER_MSG_NTC_2_OPEN |
| F4048 |
SER_MSG_ABL_VALVE_DEFECT |
| F4049 |
SER_MSG_ABL_VALVE_CLOGGED |
| F4050 |
SER_MSG_ABL_VALVE_LEAKY |
| F4051 |
SER_MSG_SLT_FU_COM_FAULT |
| F4052 |
SER_MSG_MFM1_FAULT |
| F4053 |
SER_MSG_MFM2_FAULT |
| F4054 |
SER_MSG_MFM3_FAULT |
| F4055 |
SER_MSG_MFM4_FAULT |
| F4056 |
SER_MSG_MFM5_FAULT |
| F4057 |
SER_MSG_TACHO_FAULT |
| F4058 |
SER_MSG_TACHO_SPG_SMALL |
| F4059 |
SER_MSG_DOOR RELEASE_1 |
| F4060 |
SER_MSG_DOOR RELEASE_2 |
| F4061 |
SER_MSG_CHIP CARD_FAULT |
| F4062 |
SER_MSG_CHIP CARD_SCHALTER |
| F4063 |
SER_MSG_MEMORY CARD_FAULT |
| F4064 |
SER_MSG_SMALL_MEMORY_CARD |
| F4065 |
SER_MSG_MEMORY |
| F4066 |
SER_MSG_CLOCK_MODUL |
| F4067 |
SER_MSG_BEL_MODUL |
| F4068 |
SER_MSG_FU_MODUL |
| F4069 |
SER_MSG_NTC_DRAWN |
| F4070 |
SER_MSG_MACHINE TYPE |
| F4071 |
SER_MSG_HEATER TYPE |
| F4072 |
SER_MSG_FAULT_BAE |
| F4073 |
MSG_DUMMY_1 |
| F4074 |
MSG_DUMMY_2 |
| F4075 |
MSG_DUMMY_3 |
| F4076 |
MSG_DUMMY_4 |
| F4077 |
MSG_DUMMY_5 |
| F4078 |
MSG_DUMMY_6 |
| F4079 |
MSG_FLIP_FLOP_ABGEFALLEN |
| F4080 |
internal fault BAE |
| F4081 |
Multi functional module EZL 230 signed in with code 1, code not recognized |
| F4082 |
Multi functional module EZL 230 signed in with code 2, code not recognized |
| F4083 |
Multi functional module EZL 230 signed in with code 3, code not recognized |
| F4084 |
Multi functional module EZL 230 signed in with code 4, code not recognized |
| F4085 |
Multi functional module EZL 230 signed in with code 5, code not recognized |
| F4086 |
Multi functional module EZL 230 signed in with code 6, code not recognized |
| F4087 |
Multi functional module EZL 230 signed in with code 7, code not recognized |
| F4088 |
Multi functional module EZL 230 signed in with code 8, code not recognized |
| F4089 |
Multi functional module EZL 230 signed in with code 9, code not recognized |
| F4090 |
Multi functional module EZL 230 signed in with code 10, code not recognized |
| F4091 |
Multi functional module EZL 230 signed in with code 11, code not recognized |
| F4092 |
Multi functional module EZL 230 signed in with code 12, code not recognized |
| F4093 |
Multi functional module EZL 230 signed in with code 13, code not recognized |
| F4094 |
Multi functional module EZL 230 signed in with code 14, code not recognized |
| F4095 |
Multi functional module EZL 230 signed in with code 15, code not recognized |
| F4096 |
Code switch 14X on ELP 230, mashine type and heater type not recognizes. Mashine type not recognized |
| F4097 |
Code switch 14X on ELP 230, mashine type and heater type not recognizes. Mashine type not recognized |
| F4098 |
fault FU |
| F4099 |
fault timer-Modul |
| F4100 |
fault data memory |
| F4101 |
fault BW-data |
| F4102 |
fault check sum operating system |
| F4103 |
fault check sum work copy |
| F4104 |
fault check sum current name |
| F4105 |
fault check sum blcok name |
| F4106 |
fault check sum programme list |
| F4107 |
fault check sum Block list |
| F4108 |
fault check sum appliance status |
| F4109 |
fault check sum Kanden setting |
| F4110 |
fault check sum Service setting |
| F4111 |
fault check sum language |
| F4112 |
fault check sum input/output-allocation |
| F4113 |
FAULT_CS_SYSTEM COMPONENT |
| F4114 |
fault check sum programme memory |
| F4115 |
fault check sum Block memory |
| F4116 |
fault check sum mashine history |
| F4117 |
fault check sum operation data |
| F4118 |
fault check sum faults statistic |
| F4119 |
fault check sum operation fault |
| F4120 |
FAULT_CS_DRYER_LOW PRESSURE TABLE |
| F4121 |
fault check sum Standard programme |
| F4122 |
fault check sum Standard block |
| F4123 |
fault Backup-matching |
| F4124 |
fault motor without rotation |
| F4125 |
time overrun (Timeout) in communication between control ELP 230 and frequency converter EFU 230. |
| F4126 |
fault drive Tacho |
| F4127 |
fault drive Tacho after safety time |
| F4128 |
fault drive Tacho in programme stop |
| F4129 |
fault drive Tacho in programme stop |
| F4130 |
fault drive FU-safety brunt |
| F4131 |
fault drive Motor klixon |
| F4132 |
FAULT_POSITION_NOT_ADJUSTED |
| F4133 |
FAULT_POSITION_ADJUSTED |
| F4134 |
fault imbalance |
| F4135 |
fault imbalance switch |
| F4136 |
fault heating system NTC1 |
| F4137 |
fault heating system NTC1 Desinfection |
| F4138 |
fault heating system TGS a contact |
| F4139 |
relay contact 13,14 on 1K1/1 and/or 2K1/1 interrupted in heat up phase |
| F4140 |
relay contact 13,14 an 1K1/1 and 2K1/1 closed outside heat up phase |
| F4141 |
FAULT_HEATING SYSTEM_TGS_DURING_HEATING PHASE |
| F4142 |
FAULT_HEATING SYSTEM_TGS_MEMORY |
| F4143 |
FAULT_THERMOSTOP |
| F4144 |
switch door lock 2F6/6 does not switch or motorklixon F3 has tripped |
| F4145 |
FAULT_DOOR LOCK_RELEASE |
| F4146 |
FAULT_DOOR LOCK_DOOR_OPEN |
| F4147 |
FAULT_DOOR LOCK_DOOR_CLOSE |
| F4148 |
FAULT_DOOR RELEASE SIGNAL |
| F4149 |
fault Notentriegelung door open |
| F4150 |
FAULT_SAFETY LOCK_DOOR_CLOSED |
| F4151 |
no level increase within 5 minutes. |
| F4152 |
switch 3S57 interruption |
| F4153 |
Analog pressure sensor recognize overflow level or is faulty |
| F4154 |
fault drainage |
| F4155 |
fault drainage spin |
| F4156 |
safety pilot notifies a fault (F10, exit 3) |
| F4157 |
level switch 2B1/13 has connected (contact 1-3 closed) |
| F4158 |
level switch 1B1/13 has connected (contact 1-2 closed) |
| F4159 |
fault check dispenser system F4160 Until ID 846: level switch B1/1, contact 1-3, when dispenser open. From ID 1000: electric connector on dispenser module (plug 40X GND-IN 7 defect). |
| F4161 |
timer for greasing the mount exceeded |
| F4162 |
timer for Service exceeded |
| F4163 |
timer for BGR-check exceeded |
| F4164 |
Analoger-pressure sensor on ELP 230 defect. |
| F4165 |
Interruption plug EB 230 65X, to ELP 230 30X. Or EB 230 defect. |
| F4166 |
fault cradle system in programme F4167 fault net interruption |
| F4168 |
FAULT_CHIP CARD_SLT |
| F4169 |
FAULT_CHIP CARD_BAE |
| F4170 |
To ID 846: internal fault status 1 door state. From ID 1000: internal fault control at data back-up Service setting |
| F4171 |
To ID 846: internal fault Status 2 door state. From ID 1000: internal fault of control at data back-up of the input/output list |
| F4172 |
To ID 846: internal fault Status 3 doort status. From ID 1000: internal fault of control at data back-up of system parts list |
| F4173 |
FAULT_PROGRAMME LIST |
| F4174 |
internal fault |
| F4175 |
FAULT_INTERRUPT |
| F4176 |
FAULT_TASK |
| F4177 |
internal fault |
| F4178 |
internal fault |
| F4179 |
internal fault |
| F4180 |
internal fault |
| F4181 |
internal fault |
| F4182 |
internal fault |
| F4183 |
FAULT_FANKLIXON_INTERNAL_RUNNING |
| F4184 |
FAULT_FANKLIXON_EXTERNAL_RUNNING |
| F4185 |
FAULT_TEMPERATURE_BEFORE_START |
| F4186 |
fault copy flashcard |
| F4187 |
internal fault |
| F4188 |
internal fault |
| F4189 |
internal fault |
| F4190 |
internal fault |
| F4191 |
internal fault |
| F4192 |
internal fault |
| F4193 |
internal fault |
| F4194 |
internal fault |
| F4195 |
internal fault |
| F4196 |
internal fault |
| F4197 |
internal fault |
| F4198 |
internal fault |
| F4199 |
internal fault |
| F4200 |
internal fault |
| F4201 |
internal fault |
| F4202 |
internal fault |
| F4203 |
internal fault |
| F4204 |
ROOM THERMOSTAT_8F1 |
| F4205 |
ROOM THERMOSTAT_9F1 |
| F4206 |
FAULT_EXHAUST AIR_NTC |
| F4207 |
FAULT_TOOLUFT_NTC |
| F4208 |
FAULT_PRESSURE GAUGE_TR |
| F4209 |
internal fault |
| F4210 |
internal fault |
| F4211 |
internal fault |
| F4212 |
internal fault |
| F4213 |
FAULT_DUMMY_6 |
| F4214 |
internal fault |
| F4215 |
internal fault |
| F4216 |
internal fault |
| F4217 |
internal fault |
| F4218 |
internal fault |
| F4219 |
internal fault |
| F4220 |
internal fault |
| F4221 |
internal fault |
| F4222 |
internal fault |
| F4223 |
internal fault |
| F4224 |
internal fault |
| F4225 |
internal fault |
| F4226 |
internal fault |
| F4227 |
internal fault |
| F4228 |
internal fault |
| F4229 |
internal fault |
| F4230 |
internal fault |
| F4231 |
internal fault |
| F4232 |
internal fault |
| F4233 |
internal fault |
| F4234 |
internal fault |
| F4235 |
internal fault |
| F4236 |
internal fault |
| F4237 |
internal fault |
| F4238 |
internal fault |
| F4239 |
internal fault |
| F4240 |
internal fault |
| F4241 |
internal fault |
| F4242 |
internal fault |
| F4243 |
internal fault |
| F4244 |
internal fault |
| F4245 |
internal fault |
| F4246 |
internal fault |
| F4247 |
internal fault |
| F4248 |
internal fault |
| F4249 |
internal fault |
| F4250 |
internal fault |
| F4251 |
internal fault |
| F4252 |
internal fault |
| F4253 |
internal fault |
